Citation: | JIA Xiaomeng, SUN Xihuan, LI Yongye. Influences of hydrocyclone structural parameters on the spiral flow of concentric annular gap[J]. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 2023, 39(24): 23-32. DOI: 10.11975/j.issn.1002-6819.202305057 |
A pipe hydrocyclone is easy to disassemble in agricultural machinery. Spiral flow can be generated to drive the movement of impurities in the pipe, thereby effectively reducing the accumulation of impurities. Different structural parameters can form differences in the annular gap space of hydrocyclones. The structure of the annular gap space can also dominate the flow field distribution and swirl efficiency. Therefore, this article aims to explore the annular gap spiral flow formed by the hydrocyclones with different structural parameters using physical model experiments. The research results show that the structural parameters of hydrocyclone were dominated by the magnitude and dispersion of axial, radial and circumferential flow rates, where the most contribution was the radial and circumferential flow rates. There was no change in the overall distribution pattern of the annular gap flow field. Furthermore, there was the roughly same variation trend of axial average velocity and standard deviation along the water flow direction under different structural parameters. Both showed a gradually decreasing trend along the way. However there was a relatively small amplitude of the decrease in the axial average velocity along the way. The standard deviation of the cross-section gradually decreased in the constant diameter of the hydrocyclone, as the length increased, whereas, the axial average velocity increased. However, there were relatively small changes in the standard deviation and axial average velocity. Both axial average flow velocity and standard deviation increased in the constant length of the hydrocyclone, as the diameter increased, whereas, there was a relatively large variation in their amplitude. The radial average velocity and standard deviation showed a "V" shaped trend of decreasing first and then increasing along the flow under different structural parameters. The radial average velocity and flow velocity fluctuation of each section gradually increased in the constant diameter of hydrocyclone, as the length increased, but the increase was relatively small. The radial average velocity decreased in the constant length of hydrocyclone, as the diameter increased, but the flow velocity fluctuation of each section increased gradually. The circumferential average velocity and standard deviation of different structural parameters showed a gradually increasing trend along the water flow, but their growth rate in the first half of the annular gap was relatively small. The circumferential average velocity and flow velocity fluctuation showed a gradually increasing trend in the constant diameter of hydrocyclone, as the length increased, but the increased amplitude of both was relatively small. The circumferential average velocity and flow velocity fluctuation showed a gradually increasing trend in the constant length of hydrocyclone, as the diameter increased. Both energy consumption and rotation efficiency increased significantly, as the length or diameter of hydrocyclone increased. In addition, there was a higher increase rate with the diameter than that with the length. This experiment demonstrated that the hydrocyclone with a structural parameter of 70 mm×100 mm presented the highest starting efficiency. The optimal structural parameter of hydrocyclone was in the size of 70 mm×100 mm. This finding can provide a strong theoretical basis and reference for the selection and structural optimization of the hydrocyclone.
[1] |
高占义. 我国灌区建设及管理技术发展成就与展望[J]. 水利学报,2019,50(1):88-96.
GAO Zhanyi. Technical achievement and prospection in irrigation scheme development and management in China[J]. Journal of Hydraulic Engineering, 2019, 50(1): 88-96. (in Chinese with English abstract)
|
[2] |
AME M A, CAI S H. Economic pipe diameter of laterals in small tube irrigation system[J]. Alexandria Engineering Journal, 2022, 61(7): 5361-5370. DOI: 10.1016/j.aej.2021.10.057
|
[3] |
刘睿哲. 管网系统优化方法及辅助设计软件研究[D]. 杨凌:西北农林科技大学,2022.
LIU Ruizhe. Research on Optimization Method and Aided Design Software for Pipe Network System[D]. Yangling: Northwest A&F University, 2022. (in Chinese with English abstract)
|
[4] |
白静,谢崇宝. 灌溉输水管道现状及发展需求[J]. 中国农村水利水电,2018(4):34-39. DOI: 10.3969/j.issn.1007-2284.2018.04.007
BAI Jing, XIE Chongbao. Current situation and development needs of irrigation water pipelines[J]. China Rural Water and Hydropower, 2018(4): 34-39. (in Chinese with English abstract) DOI: 10.3969/j.issn.1007-2284.2018.04.007
|
[5] |
SU M X, JIAO X Y, LI J, et al. Accuracy and reliability analysis of pipe irrigation metering device for sandy water source[J]. Water, 2021, 13(7): 1-14.
|
[6] |
汪怡然,俞晓东,石林,等. 输水管道含沙水锤模型及特性研究[J]. 水利学报,2022,53(8):984-990.
WANG Yiran, YU Xiaodong, SHI Lin, et al. Models and characteristics of sand-contained water hammer in water transfer conduit[J]. Journal of Hydraulic Engineering, 2022, 53(8): 984-990. (in Chinese with English abstract)
|
[7] |
汪怡然,俞晓东,韩笑笑,等. 考虑泥沙颗粒影响的长距离供水工程单向塔水锤防护[J]. 农业工程学报,2023,39(4):84-91.
WANG Yiran, YU Xiaodong, HAN Xiaoxiao, et al. One- way surge tank protection of sediment-laden water hammer on long-distance water supply projects[J]. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 2023, 39(4): 84-91. (in Chinese with English abstract)
|
[8] |
周昊. 液固螺旋流对管道冲刷腐蚀影响研究[D]. 扬州:扬州大学,2022.
ZHOU Hao. Study on the influence of liquid-solid swirling Flow on Erosion-corrosion in Pipeline[D]. Yangzhou: Yangzhou University, 2022. (in Chinese with English abstract)
|
[9] |
HUANG B, LI X H, FU C, et al. The mechanism of drainage gas recovery and structure optimization of an internal vortex tool in a horizontal well[J]. Journal of Natural Gas Science and Engineering, 2019, 67: 233-241. DOI: 10.1016/j.jngse.2019.05.005
|
[10] |
TSUYOSHI T, YUYA I, KAZUYA U, et all. Influence of swirling flow or mass and momentum transfer downs- tream of a pipe with elbow and orifice[J]. International Journal of Heat and Mass Transfer, 2016, 92: 394-402. DOI: 10.1016/j.ijheatmasstransfer.2015.08.087
|
[11] |
王树立,饶永超,武玉宪,等. 以纽带起旋的气液螺旋流实验研究[J]. 水动力学研究与进展 A 辑,2013,28(1):105-110.
WANG Shuili, RAO Yongchao, WU Yuxian, et al. Experimental study on gas-liquid spiral flow generated by twist tape[J]. Chinese Journal of Hydrodynamics, 2013, 28(1): 105-110. (in Chinese with English abstract)
|
[12] |
ALFRED H, NISSAN, BRESAN V P. Swirling flow in cylinders[J]. Aiche Journal, 1961, 7(4): 543-547. DOI: 10.1002/aic.690070404
|
[13] |
ARDALAN J, HAKAN N. LES and DES of strongly swirling turbulent flow through a suddenly expanding circular pipe[J]. Computers and Fluids, 2015, 107: 301-313. DOI: 10.1016/j.compfluid.2014.11.014
|
[14] |
MARINS L P M, DUARTE D G, LOUREIRO G B R. LDA and PIV characterization of the flow in a hydrocyclone without an air-core[J]. Journal of Petroleum Science & Engineering, 2010, 70(3/4): 168-176.
|
[15] |
LIU W, LV X, BAI B. Axial development of air-water annular flow with swirl in a vertical pipe[J]. International Journal of Multiphase Flow, 2020, 124: 1-16.
|
[16] |
SONG X T, SUN X H, LI Y Y, et al. Exploration of the circumferential velocity structure induced by guide vane-type spiral flow generators in a pipe flow[J]. Journal of Hydraulic Engineering, 2023, 149(12):1-15.
|
[17] |
张晓雷,刘书瑜,郭利霞,等. 导流片对弧度弯管输水性能影响的数值模拟[J]. 中国农村水利水电,2023(6):161-167. DOI: 10.12396/znsd.221331
ZHANG Xiaolei, Liu Shuyu, Guo Lixia, et al. Numerical simulation of the effect of deflector sheet on the water transmission performance of curved bends[J]. China Rural Water and Hydropower, 2023(6): 161-167. (in Chinese with English abstract) DOI: 10.12396/znsd.221331
|
[18] |
张港,孙西欢,李永业,等. 不同导叶高度起旋器出口断面水力特性[J]. 排灌机械工程学报,2023,41(8):803-808.
ZHANG Gang, SUN Xihuan, LI Yongye, et al. Hydraulic characteristics of outlet section of hydrocyclone with different guide vane height[J]. Journal of Drainage and Irrigation Machinery Engineering, 2023, 41(8): 803-808. (in Chinese with English abstract)
|
[19] |
杨校礼,邓西平,吴嘉轩,等. 圆管螺旋流不同粒径粗沙输运特性试验研究[J]. 水电能源科学,2022,40(10):187-190. DOI: 10.20040/j.cnki.1000-7709.2022.20220436
YANG Xiaoli, DENG Xiping, WU Jiaxuan, et al. Experimental study on transport characteristics of coarse sand with different particle sizes in spiral pipe low[J]. Water Resources and Power, 2022, 40(10): 187-190. (in Chinese with English abstract) DOI: 10.20040/j.cnki.1000-7709.2022.20220436
|
[20] |
刘莉,白博峰. 基于可视化和图像处理的气液螺旋两相流流型研究[J]. 工程热物理学报,2022,43(11):2978-2985.
LIU Li, BAI Bofeng. Characteristics of swirling gas-liquid flow induced by a vane-type swirler[J]. Journal of Engin- eering Thermophysics, 2022, 43(11): 2978-2985. (in Chinese with English abstract)
|
[21] |
刘雯,李华峥,王雪,等. 水平管气液衰减螺旋流的流型及压降发展[J]. 机械工程学报,2020,56(20):214-222.
LIU Wen, LI Huazheng, WANG Xue, et al. Development of flow pattern and pressure drop in gas-liquid swirl flow inside horizontal pipe[J]. Journal of Mechanical Engineering, 2020, 56(20): 214-222. (in Chinese with English abstract)
|
[22] |
刘雯,李华峥,王雪,等. 水平管气液螺旋流流型辨识及压降波动研究[J]. 工程热物理学报,2021,42(1):155-164.
LIU Wen, LI Huazheng, WANG Xue, et al. Flow patterns identification and fluctuation of pressure drop in the gas- liquid swirl flow inside a horizontal pipe[J]. Journal of Engineering Thermophysics, 2021, 42(1): 155-164. (in Chinese with English abstract)
|
[23] |
张春晋,孙西欢,李永业,等. 螺旋流起旋器内部流场水力特性数值模拟与验证[J]. 农业工程学报,2018,34(1):53-62.
ZHANG Chunjin, SUN Xihuan, LI Yongye, et al. Numerical simulation and verification of hydraulic characteristics of internal flow field in spiral flow generator[J]. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 2018, 34(1): 53-62. (in Chinese with English abstract)
|
[24] |
刘雯,王雪,吕孝飞,等. 垂直管内气液螺旋流的衰减特性研究[J]. 工程热物理学报,2022,43(1):128-138.
LIU Wen, WANG Xue, LV Xiaofei, et al. Study on decay characteristics of gas-liquid swirling flow in vertical pipe[J]. Journal of Engineering Thermophysics, 2022, 43(1): 128-138. (in Chinese with English abstract)
|
[25] |
姜佑明. 基于均匀试验的水力旋流器工作效率分析及参数优化[J]. 铁道科学与工程学报[J]. 2022, 19(8):2428-2436.
JIANG Youming. Efficiency analysis and parameter optimization of hydrocyclone based on uniform tests[J]. 2022, 19(8): 2428-2436. (in Chinese with English abstract)
|
[26] |
郑伟,李鑫,贾晓萌,等. 不同导流条安放角下管道双车车间断面周向流速分布特性[J]. 水电能源科学,2022,40(2):193-196.
ZHENG Wei, LI Xin, JIA Xiaomeng, et al. Circumferential velocity distribution characteristics of two- pipe vehicles with different installation angles of guide strips[J]. Water Resources and Power, 2022, 40(2): 193-196. (in Chinese with English abstract)
|
[27] |
王子文,饶永超,李立军,等. 导流条安放角对气固两相螺旋流动特性的影响[J]. 石油机械,2020,48(4):125-134.
WANG Ziwen, RAO Yongchao, LI Lijun, et al. Effect of the angle of the guide strip on the gas-solid two-phase spiral flow behavior[J]. China Petroleum Machinery, 2020, 48(4): 125-134. (in Chinese with English abstract)
|
[28] |
LI Y Y, TAO S Y, SONG X T, et al. Study on internal Flow characteristics of hydrocyclone with guide vanes[J]. Sustainability, 2023, 15(6): 5350-5350. DOI: 10.3390/su15065350
|
[29] |
吴剑. 管道双车在不同车距下的环状缝隙螺旋流速度特征研究[D]. 太原:太原理工大学,2018.
WU Jian. Study on the Velocity Characteristics of Annular Slit Spiral Flow of Double Piped Cars Under Different Spacing[D]. Taiyuan: Taiyuan University of Technology, 2018. (in Chinese with English abstract)
|
[30] |
吴持恭. 水力学[M]. 北京:高等教育出版社,2003.
|